userdoc:board_qotom_q190g4n-s07

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
userdoc:board_qotom_q190g4n-s07 [2019/01/31 08:59]
mkeuter 		userdoc:board_qotom_q190g4n-s07 [2025/01/06 10:35] (current)
abelbeck
Line 3: Line 3:
 !!Note: AstLinux 1.2.10 or later is required!! !!Note: AstLinux 1.2.10 or later is required!!
  
-**Board Specifications:**  [[http://doc.astlinux-project.org/_media/userdoc:qotom-q190g4n-s07-motherboard-manual.pdf|Q1900G4 Nano Motherboard]]+**Board Specifications:**  [[https://doc.astlinux-project.org/_media/userdoc:qotom-q190g4n-s07-motherboard-manual.pdf|Q1900G4 Nano Motherboard]]
  
 **Vendor:** [[http://www.qotom.net/product/36.html|Product Page]] ((there is also a nearly identical [[http://www.qotom.net/product/35.html|Q190G4U]] version in a slightly different design)) **Vendor:** [[http://www.qotom.net/product/36.html|Product Page]] ((there is also a nearly identical [[http://www.qotom.net/product/35.html|Q190G4U]] version in a slightly different design))
Line 18: Line 18:
 **Total System Power (no VGA connection):**  7 Watts when idle. **Total System Power (no VGA connection):**  7 Watts when idle.
  
-**Performance:**  37.6 secs. (Maximum OpenVPN: 125 Mbps)+**Performance:**  28.2 secs. (Single-core test, lower is better)
  
-  openvpn --genkey --secret /tmp/secret +  time ( echo "scale=3456; 4*a(1)" | bc -l )
-  time openvpn --test-crypto --secret /tmp/secret --verb 0 --tun-mtu 20000 --cipher aes-256-cbc+
  
 **Configuration:** **Configuration:**
Line 72: Line 71:
 Save the above BIOS changes, reboot. Save the above BIOS changes, reboot.
  
-!!Note:!! On newer BIOS versions (12/2018) you might need to make the following changes, if you can't boot the AstLinux installation from an USB 2.0 stick:+!!Note:!! On newer BIOS versions (12/2018) you might need to make the following changes, if you can't boot the AstLinux installation from an USB stick:
  
-In „Chipset/South Bridge/USB Configuration“:+In "Chipset/South Bridge/USB Configuration":
  
-  * "XHCI Mode" to Disabled +  * ''XHCI Mode -> Disabled'' 
-  * "USB 2.0(EHCI) Support“ to Enabled+  * ''USB 2.0(EHCI) Support -> Enabled'' 
 + 
 +If the mSATA was pre-installed (with e.g. PFSense) you also need to setup the Boot Priorities for the USB stick correctly on the "Boot" page.\\  
 +Or you can choose a temporary Boot-Device at the „Save & Exit“ tab under „Boot Override“ at the bottom (instead of a Boot-Menu). 
 + 
 +!!Update:!! To activate the boot menu, press F11 (or F7 on some models).
  
 **Photos:** **Photos:**
Line 86: Line 90:
  
 {{:userdoc:qotom-q190g4n-s07-inside.jpg?nolink|Inside}} {{:userdoc:qotom-q190g4n-s07-inside.jpg?nolink|Inside}}
 +
 +**Qotom Q190G4U (alternative model)**
 +
 +{{:userdoc:qotom-q190g4u-s01-back.jpg?nolink&650|Q190G4U Back}}
  
 \\ \\
  • userdoc/board_qotom_q190g4n-s07.1548946746.txt.gz
  • Last modified: 2019/01/31 08:59
  • by mkeuter