Differences

This shows you the differences between two versions of the page.

--- userdoc:board_jetway_nf9hql-525 [2012/12/22 12:11] – droemel
+++ userdoc:board_jetway_nf9hql-525 [2019/07/25 03:36] (current) – abelbeck
@@ Line 7: / Line 7: @@
 **AstLinux Board Type:**
-  * "geni586-serial" (19200 baud serial console)
+  * "genx86_64-serial" (Serial Console: ''19200'' baud for AstLinux 1.2.10 and earlier, ''115200'' baud for AstLinux 1.3.0 and later)
 **Complete System Recommended Options:**
@@ Line 19: / Line 19: @@
           * Fan: (included on NF9HQL-525 board heat sink)
       * __With PCIe Expansion Card Support__
-          * Jetway Case JC-11x-B Series (or similar)
+          * Jetway Case JC-11x-B Series((only a **PCI**-riser-card is included with the JC-11x-B case, no **PCIe**-riser!)) (or similar)
           * AC Adapter (brick) is included, Internal ATX Power Supply not used
           * 2 System Fans are included
@@ Line 25: / Line 25: @@
 **Total System Power (no PCIe Expansion Card):**  15 Watts when idle.
+**Performance:**  ~50 secs. (Single-core test, lower is better)
+  time ( echo "scale=3456; 4*a(1)" | bc -l )
 **Configuration:**
@@ Line 42: / Line 46: @@
   # libsensors configuration file
   # -----------------------------
-  # Jetway NF9HQL-525/NF96FL-525/NF99FL-525 Dual Core Atom
+  # Jetway NF9HQL-525 Dual Core Atom
-  chip "f71808e-*" "f71808a-*" "f71862fg-*" "f71869-*" "f71869a-*" "f71882fg-*" \
+  chip "f71882fg-*" "f71869a-*"
-       "f71889fg-*" "f71889ed-*" "f71889a-*"
-  ignore in1
   ignore in2
   ignore in3
-  ignore in4
-  ignore in5
-  ignore in6
   # Comment-out installed fan(s)
@@ Line 59: / Line 58: @@
   ignore fan3
-  label in0 "+3.3V"
+  label in0 "3.3V"
+  label in1 "VCORE"
+  label in4 "VDIMM"
+  label in5 "5V"
+  label in6 "12V"
   label in7 "3VSB"
   label in8 "Vbat"
@@ Line 71: / Line 74: @@
   label temp3 "SYS Temp2"
-  compute in0  @*2, @/2
+  compute in0 @*2, @/2
-  compute in7  @*2, @/2
+  compute in4 @*(1.5), @/(1.5)
-  compute in8  @*2, @/2
+  compute in5 @*(3.7), @/(3.7)
+  compute in6 @*(11), @/(11)
+  compute in7 @*2, @/2
+  compute in8 @*2, @/2
 \\
@@ Line 86: / Line 92: @@
 First, configure your serial terminal program to support ANSI color and 115200 baud.  If you are using minicom be sure to add the ' ''-c on'' ' option to the minicom command line, otherwise the ANSI colors will not be distinguishable in the BIOS Setup screen.
+!!Note ->!! Leave ''Serial Port Mode -> 115200 8,n,1'' for AstLinux 1.3.0 and later.
 Second, on startup type F4 (<ESC>OS) to enter the BIOS Setup, go to the "Integrated Peripherals" -> "Remote Access Configuration" .  Make the following changes...
@@ Line 103: / Line 111: @@
 The above example slows the CPU fan for normal operation and reduces the noise.
-Finally, save the above BIOS changes, reboot, and reconfigure you serial terminal program to 19200 baud, this will match what AstLinux expects.
+Finally, save the above BIOS changes, reboot, and reconfigure you serial terminal program if you changed the baud rate.
 **Photos:**
@@ Line 113: / Line 121: @@
 {{:userdoc:jetway_nf9hql-525-back.jpg?nolink|Back}}
-\\
+\\