userdoc:board_jetway_jbc430u941

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
userdoc:board_jetway_jbc430u941 [2019/11/18 21:52] – abelbeckuserdoc:board_jetway_jbc430u941 [2025/03/05 16:31] (current) – abelbeck
Line 4: Line 4:
  
 **Board Specifications:**  [[https://www.jetwaycomputer.com/JBC430U941.html|JBC430U941 / HBJC430U941]] [[https://www.jetwaycomputer.com/spec/JBC430U941.pdf|Datasheet]] **Board Specifications:**  [[https://www.jetwaycomputer.com/JBC430U941.html|JBC430U941 / HBJC430U941]] [[https://www.jetwaycomputer.com/spec/JBC430U941.pdf|Datasheet]]
 +
 +  * 4x Intel I211 NICs (1G/100M/10M speeds)
  
 **AstLinux Board Type:** **AstLinux Board Type:**
Line 17: Line 19:
 **Total System Power (no HDMI connection):**  6.5 Watts when idle. **Total System Power (no HDMI connection):**  6.5 Watts when idle.
  
-**Performance:**  34.9 secs. (Single-core test, lower is better) +**Performance:**  24.9 secs. (Single-core test, lower is better) 
  
   time ( echo "scale=3456; 4*a(1)" | bc -l )   time ( echo "scale=3456; 4*a(1)" | bc -l )
Line 43: Line 45:
 **BIOS Setup for Restore AC Power Loss:** **BIOS Setup for Restore AC Power Loss:**
  
-The Energy-Related Products Directive (ERP) is the European Commission Directive required for products sold and exported to the EU.  As such the Qotom Q530G6 does not automatically power on after a power failure.  Obviously this //feature// needs to be disabled.+The Energy-Related Products Directive (ERP) is the European Commission Directive required for products sold and exported to the EU.  As such the Jetway N3160 does not automatically power on after a power failure.  Obviously this //feature// needs to be disabled.
  
 On startup (quickly) press the ''<ESC>'' key to enter the BIOS Setup, go to the "Chipset" -> "South Bridge" .  Make the following changes... On startup (quickly) press the ''<ESC>'' key to enter the BIOS Setup, go to the "Chipset" -> "South Bridge" .  Make the following changes...
Line 50: Line 52:
  
 \\ \\
-**BIOS Setup for Boot Option Filter (non-UEFI):**+**BIOS Setup for Boot OS Selection (non-UEFI):**
  
-While in the BIOS Setup as above, check to make sure Legacy only boot is enabled, go to the "Advanced" -> "CSM Configuration" menu...+While in the BIOS Setup as above, to enable Legacy boot, go to the "Advanced" -> "CSM Configuration" menu...
  
   * ''Boot Option Filter -> Legacy Only''   * ''Boot Option Filter -> Legacy Only''
 +
 +\\
 +**BIOS Setup for Boot OS Selection (UEFI):**
 +
 +!!UEFI Boot requires AstLinux 1.4.6 or later!! - additionally RUNNIX 0.6.10 or later is needed.
 +
 +While in the BIOS Setup as above, to enable UEFI boot, go to the "Advanced" -> "CSM configuration" menu...
 +
 +  * ''Boot option filter -> UEFI Only''
  
 \\ \\
  • userdoc/board_jetway_jbc430u941.1574113956.txt.gz
  • Last modified: 2019/11/18 21:52
  • by abelbeck