Differences

This shows you the differences between two versions of the page.

--- userdoc:tt_asterisk-gui [2012/04/09 16:04]
abelbeck
+++ userdoc:tt_asterisk-gui [2015/05/16 11:08] (current)
abelbeck [Using the Asterisk GUI]
@@ Line 4: / Line 4: @@
 The Asterisk GUI is an open source project created by [[http://www.digium.com/|Digium]], allowing the Asterisk configuration to be created, edited and managed via a web browser.  If you prefer to edit the Asterisk configuration via a text editor or via the Edit tab in the AstLinux Web Interface, do not use the Asterisk GUI without first understanding how the Asterisk GUI re-writes the configuration files.
+!!Note: Asterisk GUI is no longer supported with AstLinux 1.2.3 and later.!!
+===== Configuration Files =====
 Two files are key to allowing the Asterisk GUI to operate, located at:
@@ Line 9: / Line 12: @@
   * ''/mnt/kd/asterisk/http.conf'' (or a symlink as ''/etc/asterisk/http.conf'')
-===== manager.conf =====
+Additionally, if the file ''/mnt/kd/dahdi/system.conf'' does **not** exist, create it with the CLI command:
+  cp /stat/etc/dahdi/system.conf /mnt/kd/dahdi/system.conf
+===== Asterisk manager.conf =====
+The default ''manager.conf'' should contain these settings, without editing:
   [general]
@@ Line 18: / Line 28: @@
   bindaddr = 0.0.0.0
+The username/password for the Asterisk GUI is defined in the ''manager.conf'' file.  Add/Edit a section similar to the following:
-The username/password for the Asterisk GUI is defined in the asterisk manager.conf file.  This file is found at ''/mnt/kd/asterisk/manager.conf'' or a symlink as ''/etc/asterisk/manager.conf'' .  This file requires a section similar to the following:
   ; THIS IS INSECURE! CHANGE THE PASSWORD!!!
@@ Line 29: / Line 38: @@
   write = system,call,log,verbose,command,agent,user,config
-===== http.conf =====
+Be sure to change the password and possibly also uncomment/edit the deny/permit lines for added security.
-Add this section if it does not already exist. Be sure to change the password and possibly also uncomment/edit the deny/permit lines for added security.  Restart asterisk for any changes to become active.
+===== Asterisk http.conf =====
+The default ''http.conf'' should contain these settings, without editing:
+  [general]
+  ;
+  enabled=yes
+  ;
+  bindaddr=0.0.0.0
+  ;
+  ; Port to bind to for HTTP sessions (default is 8088)
+  ;
+  ;bindport=8088
+  ;
+  ; Prefix allows you to specify a prefix for all requests
+  ; to the server.  The default is blank.  If uncommented
+  ; all requests must begin with /asterisk
+  ;
+  ;prefix=asterisk
+  ;
+  ; sessionlimit specifies the maximum number of httpsessions that will be
+  ; allowed to exist at any given time. (default: 100)
+  ;
+  ;sessionlimit=100
+  ;
+  ; Whether Asterisk should serve static content from http-static
+  ; Default is no.
+  ;
+  enablestatic=yes
+  ;
+  ; Redirect one URI to another.  This is how you would set a
+  ; default page.
+  ;   Syntax: redirect=<from here> <to there>
+  ; For example, if you are using the Asterisk-gui,
+  ; it is convenient to enable the following redirect:
+  ;
+  ;redirect = / /static/config/index.html
+  ;
+A new install ''http.conf'' should appear similar as above.
 ===== Asterisk GUI - URL =====
-Access the Asterisk GUI using the following URL, with\\
+Restart asterisk for any of the above file changes to become active.
-Username: admin\\
-Password 'secret from manager.conf'\\
+Access the Asterisk GUI using the following URL:
   http://pbx-ip-address:8088/static/config/index.html
+Username: admin\\
+Password: //secret// from ''manager.conf''\\