Differences

This shows you the differences between two versions of the page.

--- userdoc:board_lanner_lec-7220-n4 [2014/04/23 09:25]
abelbeck
+++ userdoc:board_lanner_lec-7220-n4 [2019/07/24 21:21] (current)
abelbeck
@@ Line 7: / Line 7: @@
 **AstLinux Board Type:**
-  * "geni586-serial" (19200 baud serial console)
+  * "geni586" (Video Console: VGA)
+  * "geni586-serial" (Serial Console: ''19200'' baud for AstLinux 1.2.10 and earlier, ''115200'' baud for AstLinux 1.3.0 and later)
+!!Note ->!! Not x86_64 compatible
 **Complete System Recommended Options:**
-  * Memory: 204-pin DDR3 1333 SO-DIMM 2GB
+  * Memory: 204-pin DDR3 1066/1333 SO-DIMM 2GB
-  * Flash Storage: Emphase Industrial Compact Flash Card 2 GB or 2.5" SATA SSD
+  * Flash Storage: Industrial Compact Flash Card 2 GB or 2.5" SATA SSD
   * Included:
       * Fanless Case
@@ Line 19: / Line 22: @@
 **Total System Power:**  14 Watts when idle.
+**Performance:**  49.2 secs. (Single-core test, lower is better)
+  time ( echo "scale=3456; 4*a(1)" | bc -l )
 **Configuration:**
@@ Line 25: / Line 32: @@
 ''/mnt/kd/rc.conf.d/user.conf''
-  SENSEMODS="w83627ehf"
+  SENSEMODS="f71882fg"
   ALERT_SOUNDS="startup shutdown"  # Optional Sounds
@@ Line 35: / Line 42: @@
   # libsensors configuration file
   # -----------------------------
-  # Lanner FW-7541D
+  # Lanner LEC-7220-N4
-  chip "w83627ehf-*" "w83627dhg-*"
+  chip "f81865f-*"
   ignore fan1
   ignore fan2
-  ignore fan3
-  ignore fan4
-  ignore fan5
-  ignore cpu0_vid
-  ignore temp3
-  label in0 "CPUVCORE"
-  label in1 "12V"
   ignore in2
-  label in3 "3VCC"
-  label in4 "5V"
+  label in0 "+3.3V"
-  label in5 "1.5V"
+  label in1 "VCORE"
-  ignore in6
+  label in3 "5V"
-  ignore in7
+  label in4 "12V"
-  label in8 "Vbat"
+  label in5 "3VSB"
+  label in6 "Vbat"
   label temp1 "SYS Temp"
   label temp2 "CPU Temp"
-  compute in1 @*(1+(150/10)), @/(1+(150/10))
+  compute in0 @*2, @/2
-  compute in4 @*(1+(30/10)),  @/(1+(30/10))
+  compute in3 @*5.255319148, @/5.255319148
-  compute in5 @*(1+(10/10)), @/(1+(10/10))
+  compute in4 @*11, @/11
+  compute in5 @*2, @/2
-  set temp1_max       90
+  compute in6 @*2, @/2
-  set temp1_max_hyst  85
-  set in0_min   0.2
-  set in0_max   2.5
-  set in1_min   12.0*0.9
-  set in1_max   12.0*1.1
-  set in3_min   3.3*0.9
-  set in3_max   3.3*1.1
-  set in4_min   5*0.9
-  set in4_max   5*1.1
-  set in5_min   1.5*0.9
-  set in5_max   1.5*1.1
-  set in8_min   3.3*0.9
-  set in8_max   3.3*1.1
 \\
@@ Line 87: / Line 73: @@
 \\
-**BIOS Setup via Serial Port:**
+**BIOS Setup:**
-While it is possibly to use a VGA cable to connect to the board's internal VGA header (cable not provided) to view the BIOS, a better solution is to use "Remote Access" to the BIOS via the serial port.
+The BIOS can be entered by using the VGA port, fortunately no change to the default BIOS settings is required.
-First, configure your serial terminal program to support ANSI color and 115200 baud.  If you are using minicom be sure to add the ' ''-c on'' ' option to the minicom command line, otherwise the ANSI colors will not be distinguishable in the BIOS Setup screen.
-Second, on startup as soon as you hear the beep, type <TAB> to enter the BIOS Setup, go to the "Advanced" -> "Remote Access Configuration" .  Make the following changes...
-  * ''Serial Port Mode -> 19200 8,n,1''
-  * ''Redirection After BIOS POST -> Disabled''
-  * ''Sredir Memory Display Delay -> Delay 4 Sec''
-The results should like the following screen...
-{{:userdoc:lanner_fw-7541d-remote-bios.png?nolink|Remote Access BIOS}}
-Finally, save the above BIOS changes, reboot, and reconfigure you serial terminal program to 19200 baud, this will match what AstLinux expects.
 **Photos:**
@@ Line 117: / Line 89: @@
 {{:userdoc:lanner_lec-7220-n4-front.jpg?nolink|Front}}