userdoc:tt_wan_failover

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
userdoc:tt_wan_failover [2019/03/31 17:17]
mknill [PPPoE on Failover Interface]
userdoc:tt_wan_failover [2021/01/19 13:15] (current)
mkeuter [AVM FRITZ!Box 6820v3 LTE as LTE Router]
Line 97: Line 97:
   exit 0   exit 0
  
 +\\
 +===== Exit Action Script (optional) =====
 +
 +!!Note: AstLinux 1.3.7 or later is required!!
 +
 +Conditionally test when a Secondary -> Primary WAN link change is allowed to occur, by executing a script.
 +
 +If this script has an exit value of ''0'' the link change occurs, else with any other exit value the failover remains on the Secondary WAN.
 +
 +The script must be found at ''/mnt/kd/wan-failover-exit.script'' and be made executable...
 +
 +  chmod 755 /mnt/kd/wan-failover-exit.script
 +
 +Example: ''/mnt/kd/wan-failover-exit.script''
 +
 +  #!/bin/sh
 +  
 +  ##
 +  ## wan-failover-exit action script
 +  ##
 +  ## Automatically called before any Secondary -> Primary WAN link change
 +  ## and the Primary WAN link is reachable.
 +  ##
 +  ## If this script has an exit value of 0 the link change occurs.
 +  ## Else with any other exit value, the failover remains on the Secondary WAN.
 +  ##
 +  ## Note: Do not 'sleep' in this script, exit promptly.
 +  ##
 +  state="$1"
 +  primary_if="$2"
 +  primary_gw="$3"
 +  secondary_if="$4"
 +  secondary_gw="$5"
 +  secondary_gw_ipv6="$6"
 +  
 +  ## Sanity check, 'state' must be set properly
 +  if [ "$state" != "SECONDARY_EXIT" ]; then
 +    exit 0
 +  fi
 +  
 +  . /etc/rc.conf
 +  
 +  ##
 +  ## Allow Secondary -> Primary WAN link change ?
 +  ##
 +  
 +  ## Custom user.conf variable, if "yes" failover will not return to the Primary WAN link
 +  if [ "$CUSTOM_WAN_FAILOVER_STICKY" = "yes" ]; then
 +    exit 1
 +  fi
 +  
 +  ## Check Asterisk active calls, remain on the Secondary WAN link until no active calls
 +  active_calls="$(asterisk -rx 'core show channels' | sed -n -r -e 's/^([0-9]+) +active +call.*$/\1/p')"
 +  if [ -n "$active_calls" ] && [ $active_calls -gt 0 ]; then
 +    exit 1
 +  fi
 +  
 +  exit 0
 +
 +\\
 ===== Testing Failover ===== ===== Testing Failover =====
  
Line 280: Line 340:
     ... do stuff ...     ... do stuff ...
   fi   fi
 +  
 +===== AVM FRITZ!Box 6820v3 LTE as LTE Router =====
 +
 +The AVM FRITZ!Box series is very common in Germany and parts of Europe. The 6820 LTE should work across Europe.
 +
 +[[https://en.avm.de/products/fritzbox/fritzbox-6820-lte/|Product Info]]
 +
 +  * on the FRITZ!Box overview page click on the 3 dots in the upper right corner and enable "Advanced View"
 +  * under "Home Network/Network/Network Settings/IP Addresses" click on "IPv4 Addresses" and change the "IPv4 Address" (to e.g. ''192.168.5.1''), cause every FRITZ!Box by default uses ''192.168.178.1'' and that can lead to problems when using VPNs or other FRITZ!Boxes.
 +  * setup your AstLinux Failover interface with a static address from the same network (best below ''.20'' because of DHCP) e.g. ''192.168.5.11'' and reboot AstLinux.
 +  * under "Internet/Permit Access" click "Add Device for Sharing" and enable the "Exposed Host" function for your AstLinux Failover interface.
  • userdoc/tt_wan_failover.1554070646.txt.gz
  • Last modified: 2019/03/31 17:17
  • by mknill