userdoc:tt_runnix

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
userdoc:tt_runnix [2010/12/19 22:47] – droemeluserdoc:tt_runnix [2022/05/31 13:34] (current) – [RUNNIX] abelbeck
Line 1: Line 1:
 ====== RUNNIX ====== ====== RUNNIX ======
  
-The AstLinux **[[system-config#unionfs|bootloader]]** RUNNIX has been updated to runnix-0.3.1 ((previously runnix-0.2.1)). This is considered an 'optional' upgrade at this time, and AstLinux 0.7.5 does not require runnix-0.3.1.\\  +It is very important to understand that while AstLinux 0.7.x uses the runnix-0.3 (or runnix-0.2.1) bootloader, AstLinux 1.0.x requires the runnix-0.4 bootloader. This change is required since the Linux Kernel differences require different squashfs image formats. 
-If you currently have problems booting with a SATA drive, or just want the latest features, after you upgrade to 0.7.5, and with internet connectivity, you may upgrade RUNNIX from the CLI by typing:+ 
 +The Web Interface may be used to upgrade RUNNIX via the System Tab.  Or, using the Command Line Interface:
  
   $ upgrade-RUNNIX-image check     (if the response looks good, then type)   $ upgrade-RUNNIX-image check     (if the response looks good, then type)
Line 11: Line 12:
  
 <code> <code>
-      ################################## +      ######################################### 
-      #  RUNNIX - AstLinux bootloader  # +      #  RUNNIX - AstLinux x86_64 bootloader  # 
-      ################################## +      ######################################### 
 +      
        runnix)  RUNNIX boot (default)        runnix)  RUNNIX boot (default)
  
Line 23: Line 24:
       xrunnix)  Use previous RUNNIX image (if any)       xrunnix)  Use previous RUNNIX image (if any)
  
-      memtest)  Run Memtest86+ v4.10+      memtest)  Run Memtest86+
 </code> </code>
 ==== Tips ==== ==== Tips ====
Line 32: Line 33:
   * For __non-serial__ consoles (i586/VIA) you can now use an alternate **[[userdoc:tt_console-kmap|keyboard mapping]]**.    * For __non-serial__ consoles (i586/VIA) you can now use an alternate **[[userdoc:tt_console-kmap|keyboard mapping]]**. 
   * For ssh to work, you may need to edit the network settings in '''/oldroot/cdrom/os/default.conf''' accordingly (''SSHPORT="2222"'' is a new variable since 0.3.0 and will not exist, when you upgrade)   * For ssh to work, you may need to edit the network settings in '''/oldroot/cdrom/os/default.conf''' accordingly (''SSHPORT="2222"'' is a new variable since 0.3.0 and will not exist, when you upgrade)
-  * By default (if not defined) the network variables are: NIC = eth0, DHCP and ssh port = 2222.+  * By default (if not defined) the network variables are:  
 +    * NIC = eth0 
 +    * IP = DHCP 
 +    * ssh port = 2222.
   * To reboot from the console you need to type '''exit''' or '''reboot -f'''. In ssh '''reboot -f''' also works.   * To reboot from the console you need to type '''exit''' or '''reboot -f'''. In ssh '''reboot -f''' also works.
 +  * You'll find the stuff that's normally in ''/oldroot/cdrom/'' now in ''/mnt/base/''
  
 \\  \\ 
  
  • userdoc/tt_runnix.1292798845.txt.gz
  • Last modified: 2010/12/19 22:47
  • by droemel