Differences

This shows you the differences between two versions of the page.

--- userdoc:tt_cf_usb_combo_booting [2011/04/18 15:26] – abelbeck
+++ userdoc:tt_cf_usb_combo_booting [2017/05/21 08:45] (current) – droemel
@@ Line 1: / Line 1: @@
 ====== CF + USB Combo Booting ======
+!!Note:!! Not supported anymore with AstLinux 1.3.x and newer!
 A new feature implemented with runnix-0.3.3 and AstLinux 0.7.8 allows the AstLinux distribution to be placed on a USB flash drive and operate just as if it were on a CF card.
@@ Line 7: / Line 9: @@
 For the case where the AstLinux system box cannot boot directly to a USB drive, there is a solution for that, by using the CF card to "boot" the USB flash drive, "CF + USB Combo Booting".  Follow steps #1 through #4 below.
-===
+  - Raw byte transfer ('dd', physdiskwrite, etc.) a RUNNIX-bootonly image to a CF card.  The RUNNIX-bootonly images are available here:
-) Raw byte transfer ('dd', physdiskwrite, etc.) a RUNNIX-bootonly image to a CF card.
+    * http://mirror.astlinux-project.org/runnix-bootonly/runnix-0.4-5781-bootonly.img.gz
-   The RUNNIX-bootonly image is available here: http://mirror.astlinux.org/runnix-bootonly/
+    * http://mirror.astlinux-project.org/runnix-bootonly/runnix-0.4-5781-bootonly-serial.img.gz
+  - Raw byte transfer ('dd', physdiskwrite, etc.) a complete AstLinux image to a USB flash drive.
+  - Mount the USB drive on a common OS (OS X, Linux, etc.).
+    - In the "os" directory edit the text file "astlinux-xxxxx.run.conf", the line beginning with KCMD=, add the space separated option rootdelay=10 after the 'astlive' value in the line.
+    - Eject the USB drive, remove the drive.
+  - Finally, install both the CF card and USB flash drive in your box for the AstLinux system. Boot as a normal installation.  All files will be stored on the USB drive.
-) Raw byte transfer ('dd', physdiskwrite, etc.) an AstLinux image to a USB flash drive.
-) Mount the USB drive on a common OS (OS X, Linux, etc.).
-   A) In the "os" directory edit the text file "astlinux-xxxxx.run.conf", the line beginning with KCMD=, add the space separated option rootdelay=10 after the 'astlive' value in the line.
-   B) Eject the USB drive, remove the drive.
-) Finally, install both the CF card and USB flash drive in your box for the AstLinux system. Boot as a normal installation.
-   All files will be stored on the USB drive.
-===
 Beginning with AstLinux 0.7.8, upgrade-run-image from the CLI or upgrades via the web interface will automatically propagate the rootdelay=10 KCMD value on upgrades, so upgrades on a USB drive works just like a CF card.  Additionally, upgrade-RUNNIX-image from the CLI, and via the web interface, will automatically mirror any RUNNIX updates to the BOOTONLY CF card if it exists.
-Note: With runnix-0.3.3 and later, advanced users will notice that this 'secondary' (Combo Booting) disk simply requires the AstLinux "os" distribution directory and a dosfslabel of RUNNIX on a small (128MB) FAT16 (or FAT32) partition together with a CF card with a RUNNIX-bootonly image.  The remainder of the unformatted 'secondary' disk will be formatted during the AstLinux setup process.  This would apply for any media type, even for media types where a raw byte transfer of the AstLinux flash image would not be appropriate.
+Note: With runnix-0.3.3 and later, advanced users will notice that this 'secondary' (Combo Booting) disk simply requires the AstLinux "os" distribution directory and a dosfslabel of RUNNIX on a small (128MB) FAT16 (or FAT32) partition together with a CF card with a RUNNIX-bootonly image.  The remainder of the unformatted 'secondary' disk will be formatted during the AstLinux setup process.  This would apply for any read-write media type, even for media types where a raw byte transfer of the AstLinux flash image would not be appropriate.