Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
userdoc:tt_asterisk-fop2-upgrade [2014/10/24 18:43] abelbeck [Upgrade FOP2 via CLI] |
userdoc:tt_asterisk-fop2-upgrade [2022/03/02 03:31] (current) mkeuter [Fixing Invalid FOP2 License] |
||
---|---|---|---|
Line 6: | Line 6: | ||
[[http:// | [[http:// | ||
- | If you have a FOP2 license, follow the steps outlined below to make sure FOP2 sees this as an " | + | If you have a FOP2 license, follow the steps outlined below to make sure FOP2 sees this as an " |
!!Note: AstLinux 1.2.1 or later is required!! | !!Note: AstLinux 1.2.1 or later is required!! | ||
Line 44: | Line 44: | ||
service fop2 test | service fop2 test | ||
+ | | ||
+ | If you'll get the error "Could not contact registration server, please try again later.", | ||
+ | / | ||
+ | |||
+ | Sometimes the " | ||
+ | |||
+ | / | ||
+ | | ||
Finally, start FOP2 with the newly updated version... | Finally, start FOP2 with the newly updated version... | ||
Line 51: | Line 59: | ||
!!Tip ->!! Should there be a problem with the new FOP2 version you may revert to the previous FOP2 version with "'' | !!Tip ->!! Should there be a problem with the new FOP2 version you may revert to the previous FOP2 version with "'' | ||
- | !!Tip ->!! If you made customizations to the FOP2 files, those file are saved in the ""''/ | + | !!Tip ->!! If you made customizations to the FOP2 files, those file are saved in the "''/ |
===== Upgrade FOP2 via Web Interface ===== | ===== Upgrade FOP2 via Web Interface ===== | ||
Line 62: | Line 69: | ||
===== Fixing Invalid FOP2 License ===== | ===== Fixing Invalid FOP2 License ===== | ||
- | An invalid license could be caused by a few reasons, if all else fails contact FOP2 support. | + | An invalid license could be caused by a few reasons, if all else fails contact FOP2 support |
First, using your original " | First, using your original " | ||
/ | / | ||
+ | | ||
+ | If you'll get the error "Could not contact registration server, please try again later.", | ||
+ | |||
+ | / | ||
If that fails, try to revoke your current license and then re-register... | If that fails, try to revoke your current license and then re-register... | ||
Line 74: | Line 85: | ||
If that fails, contact the fine folks at: [[http:// | If that fails, contact the fine folks at: [[http:// | ||
+ | |||
+ | ===== Re-Imaging with a FOP2 License ===== | ||
+ | |||
+ | If you have an installation with a license and want to rebuild or move the install to a different drive, a little planning with the following steps will make managing your FOP2 license easier. | ||
+ | |||
+ | Before you rebuild the install... | ||
+ | |||
+ | service fop2 stop | ||
+ | | ||
+ | / | ||
+ | |||
+ | It then asks for the original registration code, hopefully " | ||
+ | |||
+ | Re-Image your drive, install a fresh FOP2 package via the System tab, then via the CLI... | ||
+ | |||
+ | service fop2 test | ||
+ | | ||
+ | / | ||
+ | |||
+ | It will again ask for the original registration code, hopefully " | ||
+ |