Differences

This shows you the differences between two versions of the page.

--- userdoc:board_qotom_q750g5 [2022/04/21 16:31]
mkeuter
+++ userdoc:board_qotom_q750g5 [2022/04/22 14:04]
abelbeck
@@ Line 9: / Line 9: @@
 **Complete System Recommended Options:**
-  * Memory: DDR4 2GB
+  * Memory: 260-pin DDR4 SO-DIMM 4GB
   * Storage: mSATA SSD (PC Engines msata16 “Phison” or similar)
@@ Line 24: / Line 24: @@
   SENSEMODS="coretemp"
+  ALERT_SOUNDS="startup shutdown"  # Optional Sounds
+  ALERT_SOUNDS_OCTAVE="1"
   ## Optional USB TTY serial login
@@ Line 42: / Line 45: @@
   # coretemp CPU sensor
-**BIOS Setup**
-"Advanced" -> "Trusted Computing" -> "Security Device Support" => "[Disable]"
-"Advanced" -> "CSM Configuration" -> "Boot option filter" => "[Legacy only]" (for BIOS Mode) \\
-"Advanced" -> "CSM Configuration" -> "Boot option filter" => "[UEFI only]" (for UEFI Mode) //since AstLinux 1.4.6//
 \\
@@ Line 62: / Line 57: @@
 The results should like the following screen...
-{{:userdoc:qotom-q190g4n-s07-bios-power-on.png?nolink|BIOS Power On}}
+{{:userdoc:qotom-q750g5-bios-power-on.png?nolink&600|BIOS Power On}}
 \\
 **BIOS Setup for Boot OS Selection (non-UEFI):**
-While in the BIOS Setup as above, check to make sure Legacy Win7 boot is enabled, go to the "Boot" menu...
+While in the BIOS Setup as above, to enable Legacy boot, go to the "Advanced" -> "CSM configuration" menu...
-  * ''Boot OS Selection -> Legacy Win7''
+  * ''Boot option filter -> Legacy only''
 The results should like the following screen...
-{{:userdoc:qotom-q190g4n-s07-bios-legacy-boot.png?nolink|BIOS Legacy Boot}}
+{{:userdoc:qotom-q750g5-bios-legacy-boot.png?nolink&600|BIOS Legacy Boot}}
+\\
+**BIOS Setup for Boot OS Selection (UEFI):**
+!!UEFI Boot requires AstLinux 1.4.6 or later!! - additionally RUNNIX 0.6.10 or later is needed.
+While in the BIOS Setup as above, to enable UEFI boot, go to the "Advanced" -> "CSM configuration" menu...
+  * ''Boot option filter -> UEFI only''
+\\
+**Other BIOS Settings**
+"Advanced" -> "Trusted Computing" -> "Security Device Support" => "[Disable]"
 Save the above BIOS changes, reboot.
 If the mSATA was pre-installed (with e.g. PFSense) you also need to setup the Boot Priorities for the USB stick correctly on the "Boot" page.\\
-Or you can choose a temporary Boot-Device at the „Save & Exit“ tab under „Boot Override“ at the bottom (instead of a Boot-Menu).
+Or you can choose a temporary Boot-Device at the "Save & Exit" tab under "Boot Override" at the bottom (instead of a Boot-Menu).
 **Photos:**
+{{:userdoc:qotom-q750g5-network.jpg?nolink|Network}}
+{{:userdoc:qotom-q750g5-front.jpg?nolink|Front}}
+{{:userdoc:qotom-q750g5-inside.jpg?nolink|Inside}}
 \\