userdoc:board_qotom_q190g4n-s07

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
userdoc:board_qotom_q190g4n-s07 [2017/04/25 12:38]
abelbeck 		userdoc:board_qotom_q190g4n-s07 [2022/07/03 06:59] (current)
mkeuter
Line 1: Line 1:
 ====== Qotom Q190G4N-S07 Celeron J1900 Fanless Appliance ====== ====== Qotom Q190G4N-S07 Celeron J1900 Fanless Appliance ======
  
-!!Note: AstLinux 1.2.0 or later is required!!+!!Note: AstLinux 1.2.10 or later is required!!
  
 **Board Specifications:**  [[http://doc.astlinux-project.org/_media/userdoc:qotom-q190g4n-s07-motherboard-manual.pdf|Q1900G4 Nano Motherboard]] **Board Specifications:**  [[http://doc.astlinux-project.org/_media/userdoc:qotom-q190g4n-s07-motherboard-manual.pdf|Q1900G4 Nano Motherboard]]
 +
 +**Vendor:** [[http://www.qotom.net/product/36.html|Product Page]] ((there is also a nearly identical [[http://www.qotom.net/product/35.html|Q190G4U]] version in a slightly different design))
  
 **AstLinux Board Type:** **AstLinux Board Type:**
  
-  * "genx86_64" (VGA video console)+  * "genx86_64" (Video Console: VGA)
  
 **Complete System Recommended Options:** **Complete System Recommended Options:**
Line 14: Line 16:
   * Storage: mSATA SSD (PC Engines msata16 “Phison” or similar)   * Storage: mSATA SSD (PC Engines msata16 “Phison” or similar)
  
-**Total System Power (no VGA connection):**  5 Watts when idle.+**Total System Power (no VGA connection):**  7 Watts when idle.
  
-**Performance:**  37.6 secs. (Maximum OpenVPN: 125 Mbps)+**Performance:**  28.2 secs. (Single-core test, lower is better)
  
-  openvpn --genkey --secret /tmp/secret +  time ( echo "scale=3456; 4*a(1)" | bc -l )
-  time openvpn --test-crypto --secret /tmp/secret --verb 0 --tun-mtu 20000 --cipher aes-256-cbc+
  
 **Configuration:** **Configuration:**
Line 29: Line 30:
      
   ## Optional USB TTY serial login   ## Optional USB TTY serial login
-  ## Requires AstLinux 1.2.10 or later 
   USBTTY="yes"   USBTTY="yes"
   USBTTY_BAUD_RATE="115200"   USBTTY_BAUD_RATE="115200"
 +
 +!!More Info ->!!
 +**[[userdoc:usbtty_serial_login|USB TTY Serial Login]]**
  
 \\ \\
Line 67: Line 70:
  
 Save the above BIOS changes, reboot. Save the above BIOS changes, reboot.
 +
 +!!Note:!! On newer BIOS versions (12/2018) you might need to make the following changes, if you can't boot the AstLinux installation from an USB stick:
 +
 +In "Chipset/South Bridge/USB Configuration":
 +
 +  * ''XHCI Mode -> Disabled''
 +  * ''USB 2.0(EHCI) Support -> Enabled''
 +
 +If the mSATA was pre-installed (with e.g. PFSense) you also need to setup the Boot Priorities for the USB stick correctly on the "Boot" page.\\ 
 +Or you can choose a temporary Boot-Device at the „Save & Exit“ tab under „Boot Override“ at the bottom (instead of a Boot-Menu).
 +
 +!!Update:!! To activate the boot menu, press F11 (or F7 on some models).
  
 **Photos:** **Photos:**
Line 75: Line 90:
  
 {{:userdoc:qotom-q190g4n-s07-inside.jpg?nolink|Inside}} {{:userdoc:qotom-q190g4n-s07-inside.jpg?nolink|Inside}}
 +
 +**Qotom Q190G4U (alternative model)**
 +
 +{{:userdoc:qotom-q190g4u-s01-back.jpg?nolink&650|Q190G4U Back}}
  
 \\ \\
  • userdoc/board_qotom_q190g4n-s07.1493141903.txt.gz
  • Last modified: 2017/04/25 12:38
  • by abelbeck