userdoc:board_qotom_q190g4n-s07

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Last revision Both sides next revision
userdoc:board_qotom_q190g4n-s07 [2017/04/20 15:55]
abelbeck 		userdoc:board_qotom_q190g4n-s07 [2020/08/30 05:54]
mkeuter
Line 1: Line 1:
 ====== Qotom Q190G4N-S07 Celeron J1900 Fanless Appliance ====== ====== Qotom Q190G4N-S07 Celeron J1900 Fanless Appliance ======
  
-!!Note: AstLinux 1.2.0 or later is required!!+!!Note: AstLinux 1.2.10 or later is required!!
  
-**Board Specifications:**  [[http://doc.astlinux-project.org/_media/userdoc:qotom-q190g4n-s07-motherboard-manual.pdf|Q190G4N-S07]]+**Board Specifications:**  [[http://doc.astlinux-project.org/_media/userdoc:qotom-q190g4n-s07-motherboard-manual.pdf|Q1900G4 Nano Motherboard]] 
 + 
 +**Vendor:** [[http://www.qotom.net/product/36.html|Product Page]] ((there is also a nearly identical [[http://www.qotom.net/product/35.html|Q190G4U]] version in a slightly different design))
  
 **AstLinux Board Type:** **AstLinux Board Type:**
  
-  * "genx86_64" (VGA video console)+  * "genx86_64" (Video Console: VGA)
  
 **Complete System Recommended Options:** **Complete System Recommended Options:**
  
   * Memory: 204-pin DDR3L (1.35V) 1333/1600 SO-DIMM 2GB   * Memory: 204-pin DDR3L (1.35V) 1333/1600 SO-DIMM 2GB
-  * Storage: mSATA SSD (PC Engines msata16d “Phison” or similar)+  * Storage: mSATA SSD (PC Engines msata16 “Phison” or similar)
  
-**Total System Power (no VGA connection):**  5 Watts when idle.+**Total System Power (no VGA connection):**  7 Watts when idle.
  
-**Performance:**  37.6 secs. (Maximum OpenVPN: 100 Mbps)+**Performance:**  28.2 secs. (Single-core test, lower is better)
  
-  openvpn --genkey --secret /tmp/secret +  time ( echo "scale=3456; 4*a(1)" | bc -l )
-  time openvpn --test-crypto --secret /tmp/secret --verb 0 --tun-mtu 20000 --cipher aes-256-cbc+
  
 **Configuration:** **Configuration:**
Line 27: Line 28:
  
   SENSEMODS="coretemp"   SENSEMODS="coretemp"
 +  
 +  ## Optional USB TTY serial login
 +  USBTTY="yes"
 +  USBTTY_BAUD_RATE="115200"
 +
 +!!More Info ->!!
 +**[[userdoc:usbtty_serial_login|USB TTY Serial Login]]**
  
 \\ \\
Line 63: Line 71:
 Save the above BIOS changes, reboot. Save the above BIOS changes, reboot.
  
-\\+!!Note:!! On newer BIOS versions (12/2018) you might need to make the following changes, if you can't boot the AstLinux installation from an USB stick: 
 + 
 +In "Chipset/South Bridge/USB Configuration": 
 + 
 +  * ''XHCI Mode -> Disabled'' 
 +  * ''USB 2.0(EHCI) Support -> Enabled'' 
 + 
 +If the mSATA was pre-installed (with e.g. PFSense) you also need to setup the Boot Priorities for the USB stick correctly on the "Boot" page.\\  
 +Or you can choose a temporary Boot-Device at the „Save & Exit“ tab under „Boot Override“ at the bottom (instead of a Boot-Menu). 
 **Photos:** **Photos:**
  
Line 71: Line 88:
  
 {{:userdoc:qotom-q190g4n-s07-inside.jpg?nolink|Inside}} {{:userdoc:qotom-q190g4n-s07-inside.jpg?nolink|Inside}}
 +
 +**Qotom Q190G4U (alternative model)**
 +
 +{{:userdoc:qotom-q190g4u-s01-back.jpg?nolink&650|Q190G4U Back}}
  
 \\ \\
  • userdoc/board_qotom_q190g4n-s07.txt
  • Last modified: 2022/07/03 06:59
  • by mkeuter