userdoc:board_qotom_q10922h6 [AstLinux Documentation]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Qotom Q10922H6 Intel N100 Fanless Appliance ======

!!Note: AstLinux 1.5.10 or later is required!!

**Board Specifications:**  [[https://www.qotom.com/products/show/MinI-PC-Q10900H6-S13-Series|Mini PC Q10900H6 S13 Series]]

  * 2x Aquantia AQC113C NICs (10G/5G/2.5G/1G/100M/10M speeds)
  * 4x Intel I226-V NICs (2.5G/1G/100M/10M speeds)

**AstLinux Board Type:**

  * "genx86_64" (Video Console: HDMI)
  * “genx86_64-serial” (Serial Console: 115200 baud)

**Complete System Recommended Options:**

  * Memory: 262-Pin DDR5 (1.1V) 1Rx16 SO-DIMM 8GB (PC5-44800)
  * Storage: M.2 NVMe Type 2280 SSD (Silicon Power 128GB SP128GBP34A60M28 or similar)

**Total System Power (no HDMI connection):**  15 Watts when idle.

**Performance:**  7.5 secs. (Single-core test, lower is better) 

  time ( echo "scale=3456; 4*a(1)" | bc -l )

**Configuration:**


''/mnt/kd/rc.conf.d/user.conf''

  SENSEMODS="coretemp"
  
  ALERT_SOUNDS="startup shutdown"  # Optional Sounds
  ALERT_SOUNDS_OCTAVE="1"

\\
''/mnt/kd/sensors.conf''

  # libsensors configuration file
  # -----------------------------
  # Qotom Q10922H6
  
  # coretemp CPU sensor

\\
''/etc/rc.modules''

  ## These modules get modprobe'd when the system starts up.
  ##
  ## Comment out any modules you don't need.
  ##
  ## Ethernet support
  #8139cp
  #8139too
  #via-rhine
  #via-velocity
  #vmxnet3
  #pcnet32
  #e1000
  #e1000e
  #igb
  #r8125
  #r8169
  #tg3
  igc
  #ixgbe
  #i40e
  atlantic

\\
===== BIOS Settings =====

**BIOS Setup for Restore From AC Power Loss:**

On startup (quickly) press the ''<ESC>'' key to enter the BIOS Setup, go to the "O.E.M." menu..." .  Make the following changes...

  * ''Restore AC Power Loss -> Power On''

\\
**(Optional) BIOS Setup for Console Redirection:**

If you are using a serial console, you may want to optionally enable Console Redirection for the BIOS configuration.

Go to the "Advanced" -> "Serial Port Console Redirection" menu...

  * ''COM0''
  * ''Console Redirection -> Enabled''
  * ''Console Redirection Settings''
    * ''Terminal Type -> VT100''

  * ''Windows ... (EMS)''
  * ''Console Redirection -> Disabled''

\\
Save the above BIOS changes, reboot.

===== Photos =====

Default Network Port mapping:
  
  Port Labels
  1 (10G):  eth5
  2 (10G):  eth4
  3 (2.5G): eth1
  4 (2.5G): eth0
  5 (2.5G): eth2
  6 (2.5G): eth3

{{:userdoc:qotom-q10922h6-network.jpg?nolink|Network}}

{{:userdoc:qotom-q10922h6-front.jpg?nolink|Front}}

{{:userdoc:qotom-q10922h6-inside.jpg?nolink|Inside}}

\\