Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
userdoc:board_pcengines_apu [2014/08/18 07:52]
abelbeck
userdoc:board_pcengines_apu [2019/07/25 07:44] (current)
abelbeck
Line 3: Line 3:
 !!Note: AstLinux 1.1.7 or later is required!! !!Note: AstLinux 1.1.7 or later is required!!
  
-!!Note: PC Engines APU1 BIOS update is optional!!+!!Note: PC Engines APU1 will be discontinued in 2017, replaced by **[[userdoc:​board_pcengines_apu2|APU2]]**!!
  
-**Board Specifications:​** ​ [[http://​pcengines.ch/​apu1c.htm|apu1c]]+**Board Specifications:​** ​ [[http://​pcengines.ch/​apu1d.htm|apu1d]]
  
 **AstLinux Board Type:** **AstLinux Board Type:**
  
-  * "geni586-serial"​ (19200 ​115200 baud serial console)+  * "genx86_64-serial"​ (Serial Console: ''​19200''​ baud for AstLinux 1.2.10 and earlier, ''​115200'' ​baud for AstLinux 1.3.0 and later)
  
 **Complete System Recommended Options:** **Complete System Recommended Options:**
Line 18: Line 18:
   * Storage: mSATA SSD (or SD Card via USB internally, not recommended)   * Storage: mSATA SSD (or SD Card via USB internally, not recommended)
   * Included:   * Included:
-      * 2GB (apu1c) or 4GB (apu1d4) DRAM+      * 2GB (apu1d) or 4GB (apu1d4) DRAM
  
 **Total System Power:​** ​ 8 Watts when idle. **Total System Power:​** ​ 8 Watts when idle.
 +
 +**Performance:​** ​ 59.1 secs. (Single-core test, lower is better)
 +
 +  time ( echo "​scale=3456;​ 4*a(1)"​ | bc -l )
  
 **Configuration:​** **Configuration:​**
Line 43: Line 47:
 **Serial Console COM Port:** **Serial Console COM Port:**
  
-The board type of "geni586-serial"​ defaults to a 19200 baud serial console, unfortunately the PC Engines'​s BIOS is fixed at 115200 baud, so if you want to view the BIOS console you must change the AstLinux serial console speed to match at 115200 baud.  After+!!Note ->!! Skip this section for AstLinux 1.3.0 and later, which uses a ''​115200''​ baud rate. 
 + 
 +For AstLinux 1.2.10 and earlier, the board type of "genx86_64-serial"​ defaults to a 19200 baud serial console, unfortunately the PC Engines'​s BIOS is fixed at 115200 baud, so if you want to view the BIOS console you must change the AstLinux serial console speed to match at 115200 baud.  After
 **[[userdoc:​new-install#​persistent_storage_options_gui|persistent storage]]** **[[userdoc:​new-install#​persistent_storage_options_gui|persistent storage]]**
 has been configured, from the CLI issue the following command: has been configured, from the CLI issue the following command:
Line 59: Line 65:
   reboot=bios   reboot=bios
   ​   ​
-!!Note ->!! This reboot issue is fixed in the beta PC Engines APU1 BIOS apu140708 (8/7/2014).+!!Note ->!! This reboot issue is fixed in the beta PC Engines APU1 BIOS apu140708 (2014-07-08).
  
 \\  \\