userdoc:board_lanner_fw-7541d [AstLinux Documentation]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Lanner FW-7541D Atom D525 Fanless Appliance ======

!!Note: Requires AstLinux 1.x!!

**Board Specifications:**  [[http://www.lannerinc.com/products/x86-network-appliances/desktop/fw-7541|FW-7541D]]

**AstLinux Board Type:**

  * "genx86_64-serial" (Serial Console: ''19200'' baud for AstLinux 1.2.10 and earlier, ''115200'' baud for AstLinux 1.3.0 and later)

**Complete System Recommended Options:**

  * Memory: 204-pin DDR3 1333 SO-DIMM 2GB
  * Flash Storage: Industrial Compact Flash Card 2 GB or 2.5" SATA SSD
  * Included:
      * Fanless Case
      * AC Power Adapter (brick)
      * Serial Console cable, RJ-45 -> DB-9
      * SATA data/power cable for 2.5" SSD

**Total System Power:**  15 Watts when idle.

**Performance:**  43 secs. (Single-core test, lower is better)

  time ( echo "scale=3456; 4*a(1)" | bc -l )

**Configuration:**


''/mnt/kd/rc.conf.d/user.conf''

  SENSEMODS="w83627ehf"
  
  WDMODULE="iTCO_wdt"  # Optional Watchdog
  
  ALERT_SOUNDS="startup shutdown"  # Optional Sounds
  ALERT_SOUNDS_OCTAVE="1"

\\
''/mnt/kd/sensors.conf''

  # libsensors configuration file
  # -----------------------------
  # Lanner FW-7541D
  
  chip "w83627ehf-*" "w83627dhg-*"
  
  ignore fan1
  ignore fan2
  ignore fan3
  ignore fan4
  ignore fan5
  
  ignore cpu0_vid
  ignore intrusion0
  ignore temp3
  
  label in0 "CPUVCORE"
  label in1 "12V"
  ignore in2
  label in3 "3VCC"
  label in4 "5V"
  label in5 "1.5V"
  ignore in6
  ignore in7
  label in8 "Vbat"
  
  label temp1 "SYS Temp"
  label temp2 "CPU Temp"
  
  compute in1 @*(1+(150/10)), @/(1+(150/10))
  compute in4 @*(1+(30/10)),  @/(1+(30/10))
  compute in5 @*(1+(10/10)), @/(1+(10/10))
  
  set temp1_max       90
  set temp1_max_hyst  85
  
  set in0_min   0.2
  set in0_max   2.5
  set in1_min   12.0*0.9
  set in1_max   12.0*1.1
  set in3_min   3.3*0.9
  set in3_max   3.3*1.1
  set in4_min   5*0.9
  set in4_max   5*1.1
  set in5_min   1.5*0.9
  set in5_max   1.5*1.1
  set in8_min   3.3*0.9
  set in8_max   3.3*1.1

\\
When a Compact Flash card is used, and it supports DMA, much higher disk performance can be obtained by enabling LIBATA DMA for Compact Flash.  Enable from the CLI by issuing the following command:

  set-kcmd libata.dma=5

\\
**BIOS Setup via Serial Port:**

While it is possibly to use a VGA cable to connect to the board's internal VGA header (cable not provided) to view the BIOS, a better solution is to use "Remote Access" to the BIOS via the serial port.

First, configure your serial terminal program to support ANSI color and 115200 baud.  If you are using minicom be sure to add the ' ''-c on'' ' option to the minicom command line, otherwise the ANSI colors will not be distinguishable in the BIOS Setup screen.

!!Note ->!! Leave ''Serial Port Mode -> 115200 8,n,1'' for AstLinux 1.3.0 and later.

Second, on startup as soon as you hear the beep, type <TAB> to enter the BIOS Setup, go to the "Advanced" -> "Remote Access Configuration" .  Make the following changes...

  * ''Serial Port Mode -> 19200 8,n,1''
  * ''Redirection After BIOS POST -> Disabled''
  * ''Sredir Memory Display Delay -> Delay 4 Sec''


The results should like the following screen...

{{:userdoc:lanner_fw-7541d-remote-bios.png?nolink|Remote Access BIOS}}

Finally, save the above BIOS changes, reboot, and reconfigure you serial terminal program if you changed the baud rate.

**Photos:**

{{:userdoc:lanner_fw-7541d-inside1a.jpg?nolink|Inside 1}}

{{:userdoc:lanner_fw-7541d-inside2a.jpg?nolink|Inside 2}}

{{:userdoc:lanner_fw-7541d-inside3a.jpg?nolink|Inside 3}}

{{:userdoc:lanner_fw-7541d-top1b.jpg?nolink|Top/Front}}