Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
userdoc:board_lanner_fw-7541d [2012/10/25 21:17] abelbeck |
userdoc:board_lanner_fw-7541d [2017/06/11 09:03] abelbeck |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Lanner FW-7541D | + | ====== Lanner FW-7541D Atom D525 Fanless |
- | + | ||
- | !!Note: Preliminary Information - Not Official at this time!! | + | |
!!Note: Requires AstLinux 1.x!! | !!Note: Requires AstLinux 1.x!! | ||
- | **Board Specifications: | + | **Board Specifications: |
**AstLinux Board Type:** | **AstLinux Board Type:** | ||
- | * "geni586-serial" | + | * "genx86_64-serial" |
**Complete System Recommended Options:** | **Complete System Recommended Options:** | ||
* Memory: 204-pin DDR3 1333 SO-DIMM 2GB | * Memory: 204-pin DDR3 1333 SO-DIMM 2GB | ||
- | * Flash Storage: | + | * Flash Storage: Industrial Compact Flash Card 2 GB or 2.5" SATA SSD |
* Included: | * Included: | ||
* Fanless Case | * Fanless Case | ||
* AC Power Adapter (brick) | * AC Power Adapter (brick) | ||
- | * Serial Console cable, | + | * Serial Console cable, |
* SATA data/power cable for 2.5" SSD | * SATA data/power cable for 2.5" SSD | ||
**Total System Power: | **Total System Power: | ||
+ | |||
+ | **Performance: | ||
+ | |||
+ | openvpn --genkey --secret /tmp/secret | ||
+ | time openvpn --test-crypto --secret /tmp/secret --verb 0 --tun-mtu 20000 --cipher aes-256-cbc | ||
**Configuration: | **Configuration: | ||
Line 33: | Line 36: | ||
| | ||
ALERT_SOUNDS=" | ALERT_SOUNDS=" | ||
+ | ALERT_SOUNDS_OCTAVE=" | ||
\\ | \\ | ||
Line 41: | Line 45: | ||
# Lanner FW-7541D | # Lanner FW-7541D | ||
| | ||
- | chip " | + | chip " |
- | + | ||
- | ignore in0 | + | |
- | ignore in1 | + | |
- | ignore in2 | + | |
- | ignore in4 | + | |
- | ignore in5 | + | |
- | ignore in6 | + | |
| | ||
ignore fan1 | ignore fan1 | ||
Line 57: | Line 54: | ||
| | ||
ignore cpu0_vid | ignore cpu0_vid | ||
+ | ignore intrusion0 | ||
ignore temp3 | ignore temp3 | ||
| | ||
- | label in3 "+3.3V" | + | |
- | label in7 "3VSB" | + | label in1 " |
+ | ignore in2 | ||
+ | | ||
+ | label in4 "5V" | ||
+ | label in5 " | ||
+ | ignore in6 | ||
+ | ignore in7 | ||
label in8 " | label in8 " | ||
| | ||
Line 66: | Line 70: | ||
label temp2 "CPU Temp" | label temp2 "CPU Temp" | ||
| | ||
- | set in3_min | + | |
- | set in3_max | + | compute in4 @*(1+(30/ |
- | set in7_min | + | compute in5 @*(1+(10/ |
- | set in7_max | + | |
- | set in8_min | + | |
- | set in8_max | + | set temp1_max_hyst |
+ | |||
+ | set in0_min | ||
+ | set in0_max | ||
+ | set in1_min | ||
+ | set in1_max | ||
+ | set in3_min | ||
+ | set in3_max | ||
+ | set in4_min | ||
+ | set in4_max | ||
+ | set in5_min | ||
+ | set in5_max | ||
+ | set in8_min | ||
+ | set in8_max | ||
\\ | \\ | ||
Line 84: | Line 101: | ||
First, configure your serial terminal program to support ANSI color and 115200 baud. If you are using minicom be sure to add the ' '' | First, configure your serial terminal program to support ANSI color and 115200 baud. If you are using minicom be sure to add the ' '' | ||
+ | |||
+ | !!Note ->!! Leave '' | ||
Second, on startup as soon as you hear the beep, type <TAB> to enter the BIOS Setup, go to the " | Second, on startup as soon as you hear the beep, type <TAB> to enter the BIOS Setup, go to the " | ||
Line 96: | Line 115: | ||
{{: | {{: | ||
- | Finally, save the above BIOS changes, reboot, and reconfigure you serial terminal program | + | Finally, save the above BIOS changes, reboot, and reconfigure you serial terminal program |
**Photos:** | **Photos:** | ||
Line 104: | Line 123: | ||
{{: | {{: | ||
- | {{: | + | {{: |
+ | {{: |