userdoc:board_lanner_fw-7525b [AstLinux Documentation]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Lanner FW-7525B Atom C2358 Fanless Appliance ======

!!Note: AstLinux 1.2.0 or later is required!!

!!Note: BIOS build date of 09/23/2014 or later is suggested!!

**Board Specifications:**  [[http://www.lannerinc.com/products/x86-network-appliances/x86-desktop-appliances/fw-7525|FW-7525B]]

**AstLinux Board Type:**

  * "genx86_64-serial" (Serial Console: ''19200'' baud for AstLinux 1.2.10 and earlier, ''115200'' baud for AstLinux 1.3.0 and later)

**Complete System Recommended Options:**

  * Memory: 204-pin DDR3 1333 SO-DIMM 2GB (non-ECC)
  * Flash Storage: Industrial Compact Flash Card or 2.5" SATA3 SSD
  * Included:
      * Fanless Case
      * AC Power Adapter (brick)
      * Serial Console cable, RJ-45 -> DB-9
  * Optional:
      * SATA data/power cable/bracket for 2.5" SSD

**Total System Power:**  10 Watts when idle.

**Performance:**  34.9 secs. (Maximum OpenVPN: 154 Mbps)

  openvpn --genkey --secret /tmp/secret
  time openvpn --test-crypto --secret /tmp/secret --verb 0 --tun-mtu 20000 --cipher aes-256-cbc

**Configuration:**


''/mnt/kd/rc.conf.d/user.conf''

  SENSEMODS="coretemp w83627ehf"
  
  WDMODULE="w83627hf_wdt"  # Optional Watchdog

!!Note ->!! The ''ALERT_SOUNDS'' optional sounds does not connect to the piezo-buzzer.

\\
''/mnt/kd/sensors.conf''

  # libsensors configuration file
  # -----------------------------
  # Lanner FW-7525
  
  chip "w83627ehf-*" "w83627dhg-*"
  
  ignore fan1
  ignore fan2
  ignore fan3
  ignore fan4
  ignore fan5
  
  ignore cpu0_vid
  ignore intrusion0
  
  label in0 "VCORE"
  ignore in1
  ignore in2
  ignore in3
  label in4 "VDDR"
  label in5 "+1V"
  label in6 "+5V"
  ignore in7
  ignore in8
  
  label temp1 "SYS Temp"
  label temp2 "CPU Temp"
  label temp3 "AUX Temp"
  
  compute in0 @*(1+(1/20)), @/(1+(1/20))
  compute in6 @*(1+(30/10)), @/(1+(30/10))
  
  set temp1_max       90
  set temp1_max_hyst  85
  
  set in4_min   1.5*0.9
  set in4_max   1.5*1.1
  set in5_min   0.60
  set in5_max   1.28
  set in6_min   5*0.9
  set in6_max   5*1.1

\\
**Optional SSD:**

If a SSD is installed, it is internally connected via a SATA3 controller.  It is recommended to use a SATA3 SSD, as some older SATA2 SSD's may not reliably boot, quite possibly only an issue in isolated cases with older SATA2 SSD's with old firmware.

\\
**BIOS Setup via Serial Port:**

First, configure your serial terminal program to support ANSI color and 115200 baud.  If you are using minicom be sure to add the ' ''-c on'' ' option to the minicom command line, otherwise the ANSI colors will not be distinguishable in the BIOS Setup screen.

!!Note ->!! Leave ''Bits per second -> 115200'' for AstLinux 1.3.0 and later.

Second, on startup after you hear the beep and some text, type <TAB> to enter the BIOS Setup, go to the "Advanced" -> "Serial Port Console Redirection" .  Make the following changes...

  * ''Bits per second -> 19200''
  * ''Redirection After BIOS POST -> Bootloader''


The results should like the following screen...

{{:userdoc:lanner_fw-7525b-remote-bios.png?nolink|Console Redirection BIOS}}


Finally, save the above BIOS changes, reboot, and reconfigure you serial terminal program if you changed the baud rate.

**Photos:**

Lanner FW-7525A is shown with 6x NIC's:
\\
{{:userdoc:lanner_fw-7525b-inside.jpg?nolink|Inside}}

{{:userdoc:lanner_fw-7525b-inside-ssd3.jpg?nolink|Inside SSD}}

Above, optional SSD cable/bracket, (3 standoffs and 4 screws for 2.5" SSD):

{{:userdoc:lanner_fw-7525b-front.jpg?nolink|Top/Front}}