userdoc:board_jetway_nf9hql-525

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
userdoc:board_jetway_nf9hql-525 [2012/11/20 05:29]
droemel
userdoc:board_jetway_nf9hql-525 [2019/07/24 22:36] (current)
abelbeck
Line 1: Line 1:
 ====== Jetway NF9HQL-525 Dual Core Atom ====== ====== Jetway NF9HQL-525 Dual Core Atom ======
- 
-/* !!Note: Preliminary Information - Not Official at this time!! */ 
  
 !!Note: Requires AstLinux 1.x!! !!Note: Requires AstLinux 1.x!!
Line 9: Line 7:
 **AstLinux Board Type:** **AstLinux Board Type:**
  
-  * "geni586-serial" (19200 baud serial console)+  * "genx86_64-serial" (Serial Console: ''19200'' baud for AstLinux 1.2.10 and earlier, ''115200'' baud for AstLinux 1.3.0 and later)
  
 **Complete System Recommended Options:** **Complete System Recommended Options:**
Line 21: Line 19:
           * Fan: (included on NF9HQL-525 board heat sink)           * Fan: (included on NF9HQL-525 board heat sink)
       * __With PCIe Expansion Card Support__       * __With PCIe Expansion Card Support__
-          * Jetway Case JC-11x-B Series (or similar)+          * Jetway Case JC-11x-B Series((only a **PCI**-riser-card is included with the JC-11x-B case, no **PCIe**-riser!)) (or similar)
           * AC Adapter (brick) is included, Internal ATX Power Supply not used           * AC Adapter (brick) is included, Internal ATX Power Supply not used
           * 2 System Fans are included           * 2 System Fans are included
Line 27: Line 25:
  
 **Total System Power (no PCIe Expansion Card):**  15 Watts when idle. **Total System Power (no PCIe Expansion Card):**  15 Watts when idle.
 +
 +**Performance:**  ~50 secs. (Single-core test, lower is better)
 +
 +  time ( echo "scale=3456; 4*a(1)" | bc -l )
  
 **Configuration:** **Configuration:**
Line 44: Line 46:
   # libsensors configuration file   # libsensors configuration file
   # -----------------------------   # -----------------------------
-  # Jetway NF9HQL-525/NF96FL-525/NF99FL-525 Dual Core Atom+  # Jetway NF9HQL-525 Dual Core Atom
      
-  chip "f71808e-*" "f71808a-*" "f71862fg-*" "f71869-*" "f71869a-*" "f71882fg-*"+  chip "f71882fg-*" "f71869a-*"
-       "f71889fg-*" "f71889ed-*" "f71889a-*"+
      
-  ignore in1 
   ignore in2   ignore in2
   ignore in3   ignore in3
-  ignore in4 
-  ignore in5 
-  ignore in6 
      
   # Comment-out installed fan(s)   # Comment-out installed fan(s)
Line 61: Line 58:
   ignore fan3   ignore fan3
      
-  label in0 "+3.3V"+  label in0 "3.3V
 +  label in1 "VCORE" 
 +  label in4 "VDIMM" 
 +  label in5 "5V" 
 +  label in6 "12V"
   label in7 "3VSB"   label in7 "3VSB"
   label in8 "Vbat"   label in8 "Vbat"
Line 73: Line 74:
   label temp3 "SYS Temp2"   label temp3 "SYS Temp2"
      
-  compute in0  @*2, @/2 +  compute in0 @*2, @/2 
-  compute in7  @*2, @/2 +  compute in4 @*(1.5), @/(1.5) 
-  compute in8  @*2, @/2+  compute in5 @*(3.7), @/(3.7) 
 +  compute in6 @*(11), @/(11) 
 +  compute in7 @*2, @/2 
 +  compute in8 @*2, @/2
  
 \\ \\
Line 88: Line 92:
  
 First, configure your serial terminal program to support ANSI color and 115200 baud.  If you are using minicom be sure to add the ' ''-c on'' ' option to the minicom command line, otherwise the ANSI colors will not be distinguishable in the BIOS Setup screen. First, configure your serial terminal program to support ANSI color and 115200 baud.  If you are using minicom be sure to add the ' ''-c on'' ' option to the minicom command line, otherwise the ANSI colors will not be distinguishable in the BIOS Setup screen.
 +
 +!!Note ->!! Leave ''Serial Port Mode -> 115200 8,n,1'' for AstLinux 1.3.0 and later.
  
 Second, on startup type F4 (<ESC>OS) to enter the BIOS Setup, go to the "Integrated Peripherals" -> "Remote Access Configuration" .  Make the following changes... Second, on startup type F4 (<ESC>OS) to enter the BIOS Setup, go to the "Integrated Peripherals" -> "Remote Access Configuration" .  Make the following changes...
Line 105: Line 111:
 The above example slows the CPU fan for normal operation and reduces the noise. The above example slows the CPU fan for normal operation and reduces the noise.
  
-Finally, save the above BIOS changes, reboot, and reconfigure you serial terminal program to 19200 baud, this will match what AstLinux expects.+Finally, save the above BIOS changes, reboot, and reconfigure you serial terminal program if you changed the baud rate.
  
 **Photos:** **Photos:**
Line 115: Line 121:
 {{:userdoc:jetway_nf9hql-525-back.jpg?nolink|Back}} {{:userdoc:jetway_nf9hql-525-back.jpg?nolink|Back}}
  
-\\  
  
  
 +\\ 
  • userdoc/board_jetway_nf9hql-525.1353410964.txt.gz
  • Last modified: 2012/11/20 05:29
  • by droemel