Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
userdoc:board_jetway_nf9hql-525 [2012/11/19 09:07] abelbeck |
userdoc:board_jetway_nf9hql-525 [2017/06/11 09:15] abelbeck |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== Jetway NF9HQL-525 Dual Core Atom ====== | ====== Jetway NF9HQL-525 Dual Core Atom ====== | ||
- | |||
- | /* !!Note: Preliminary Information - Not Official at this time!! */ | ||
!!Note: Requires AstLinux 1.x!! | !!Note: Requires AstLinux 1.x!! | ||
Line 9: | Line 7: | ||
**AstLinux Board Type:** | **AstLinux Board Type:** | ||
- | * "geni586-serial" | + | * "genx86_64-serial" |
**Complete System Recommended Options:** | **Complete System Recommended Options:** | ||
Line 21: | Line 19: | ||
* Fan: (included on NF9HQL-525 board heat sink) | * Fan: (included on NF9HQL-525 board heat sink) | ||
* __With PCIe Expansion Card Support__ | * __With PCIe Expansion Card Support__ | ||
- | * Jetway Case JC-11x-B Series (or similar) | + | * Jetway Case JC-11x-B Series((only a **PCI**-riser-card is included with the JC-11x-B case, no **PCIe**-riser!)) |
* AC Adapter (brick) is included, Internal ATX Power Supply not used | * AC Adapter (brick) is included, Internal ATX Power Supply not used | ||
* 2 System Fans are included | * 2 System Fans are included | ||
Line 27: | Line 25: | ||
**Total System Power (no PCIe Expansion Card): | **Total System Power (no PCIe Expansion Card): | ||
+ | |||
+ | **Performance: | ||
+ | |||
+ | openvpn --genkey --secret /tmp/secret | ||
+ | time openvpn --test-crypto --secret /tmp/secret --verb 0 --tun-mtu 20000 --cipher aes-256-cbc | ||
**Configuration: | **Configuration: | ||
Line 44: | Line 47: | ||
# libsensors configuration file | # libsensors configuration file | ||
# ----------------------------- | # ----------------------------- | ||
- | # Jetway NF9HQL-525/ | + | # Jetway NF9HQL-525 Dual Core Atom |
| | ||
- | chip "f71808e-*" | + | chip "f71882fg-*" " |
- | " | + | |
| | ||
- | ignore in1 | ||
ignore in2 | ignore in2 | ||
ignore in3 | ignore in3 | ||
- | ignore in4 | ||
- | ignore in5 | ||
- | ignore in6 | ||
| | ||
# Comment-out installed fan(s) | # Comment-out installed fan(s) | ||
Line 61: | Line 59: | ||
ignore fan3 | ignore fan3 | ||
| | ||
- | label in0 "+3.3V" | + | label in0 "3.3V" |
+ | label in1 " | ||
+ | label in4 " | ||
+ | label in5 " | ||
+ | label in6 "12V" | ||
label in7 " | label in7 " | ||
label in8 " | label in8 " | ||
Line 73: | Line 75: | ||
label temp3 "SYS Temp2" | label temp3 "SYS Temp2" | ||
| | ||
- | compute in0 @*2, @/2 | + | compute in0 @*2, @/2 |
- | compute | + | compute |
- | compute in8 @*2, @/2 | + | compute in5 @*(3.7), @/(3.7) |
+ | compute in6 @*(11), @/(11) | ||
+ | compute in7 @*2, @/2 | ||
+ | compute in8 @*2, @/2 | ||
\\ | \\ | ||
Line 85: | Line 90: | ||
**BIOS Setup via Serial Port:** | **BIOS Setup via Serial Port:** | ||
- | While it is possibly to use a VGA cable to connect to the board' | + | While it is possibly to use a VGA cable to connect to the board' |
First, configure your serial terminal program to support ANSI color and 115200 baud. If you are using minicom be sure to add the ' '' | First, configure your serial terminal program to support ANSI color and 115200 baud. If you are using minicom be sure to add the ' '' | ||
+ | |||
+ | !!Note ->!! Leave '' | ||
Second, on startup type F4 (< | Second, on startup type F4 (< | ||
Line 105: | Line 112: | ||
The above example slows the CPU fan for normal operation and reduces the noise. | The above example slows the CPU fan for normal operation and reduces the noise. | ||
- | Finally, save the above BIOS changes, reboot, and reconfigure you serial terminal program | + | Finally, save the above BIOS changes, reboot, and reconfigure you serial terminal program |
**Photos:** | **Photos:** | ||
Line 115: | Line 122: | ||
{{: | {{: | ||
- | \\ | ||
+ | \\ |