userdoc:board_hpe_microserver_x3421

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision 		Previous revision
Next revision Both sides next revision
userdoc:board_hpe_microserver_x3421 [2019/06/02 10:04]
abelbeck created 		userdoc:board_hpe_microserver_x3421 [2019/06/02 17:56]
abelbeck
Line 7: Line 7:
 [[https://www.servethehome.com/hpe-proliant-microserver-gen10-review/|Review]] [[https://www.servethehome.com/hpe-proliant-microserver-gen10-review/|Review]]
 [[https://www.youtube.com/watch?v=v3QQBHIjtGI|Overview Video]] [[https://www.youtube.com/watch?v=v3QQBHIjtGI|Overview Video]]
 +
 +!!Note ->!! The description below applies to running AstLinux "bare metal".  Alternatively, this same hardware is well equipped to run a VM hypervisor with AstLinux running as a "guest VM". 
  
 **AstLinux Board Type:** **AstLinux Board Type:**
Line 43: Line 45:
      
   label temp1 "CPU Temp"   label temp1 "CPU Temp"
 +
 +\\
 +**BIOS NIC Setup for Ethernet PXE Boot:**
 +
 +On startup press the ''Control-S'' key to enter the BIOS NIC Setup, disable PXE boot for both ethernet NIC's.
 +
 +The results should like the following screen...
 +
 +{{:userdoc:hpe-microserver-x3421-bios-nic-pxe.png?nolink|BIOS NIC PXE}}
  
 \\ \\
Line 49: Line 60:
 The Energy-Related Products Directive (ERP) is the European Commission Directive required for products sold and exported to the EU.  As such the HPE MicroServer does not automatically power on after a power failure.  Obviously this //feature// needs to be disabled. The Energy-Related Products Directive (ERP) is the European Commission Directive required for products sold and exported to the EU.  As such the HPE MicroServer does not automatically power on after a power failure.  Obviously this //feature// needs to be disabled.
  
-On startup (quickly) press the ''F11'' key to enter the BIOS Setup, go to the "Chipset" -> "PCH-IO Configuration" .  Make the following changes...+On startup press the ''F11'' key to enter the BIOS Setup, go to the "Chipset" -> "PCH-IO Configuration" .  Make the following changes...
  
   * ''Restore On Power Loss -> Power On''   * ''Restore On Power Loss -> Power On''
Line 71: Line 82:
 Save the above BIOS changes, reboot. Save the above BIOS changes, reboot.
  
-!!Tip ->!! If you need to choose the boot drive, for example when booting the ISO Installer via a USB drive, on startup (quickly) press the ''F11'' key.+!!Tip ->!! If you need to choose the boot drive, for example when booting the ISO Installer via a USB drive, on startup press the ''F11'' key.
  
 **Photos:** **Photos:**
 +
 +{{:userdoc:hpe-microserver-x3421-front.png?nolink|Front}}
 +
 +{{:userdoc:hpe-microserver-x3421-back.png?nolink|Back}}
  
 {{:userdoc:hpe-microserver-x3421-disk-tray.jpg?nolink|Disk Tray}} {{:userdoc:hpe-microserver-x3421-disk-tray.jpg?nolink|Disk Tray}}
 +
 +2.5“ SATA SSD with ORICO 2.5 to 3.5 Hard Drive Adapter Tray
  
 \\ \\
  
  • userdoc/board_hpe_microserver_x3421.txt
  • Last modified: 2019/07/24 21:12
  • by abelbeck